From: Heiko Stuebner <heiko.stuebner@...>
Date: Tue, 12 Dec 2023 14:27:37 +0100
Apart from the host-only usb3 controller (host2) the rk3588 also provides
two dual-role controllers. On the Tiger-Haikou combination these are
connected to the lower usb3-host port in host-only mode and the micro-usb3
port for dual-role operation.
Add the necessary controllers, phys and usb-id extcon to the Tiger-Haikou
board. The Q7 standard defines the pin as usb-id, but it will only ever
get used if the baseboard actually provides an OTG port. So the extcon
stays disabled in the dtsi and only gets enabled in the haikou dts.
Signed-off-by: Heiko Stuebner <heiko.stuebner@...>
.../boot/dts/rockchip/rk3588-tiger-haikou.dts | 58 +++++++++++++++++++
.../arm64/boot/dts/rockchip/rk3588-tiger.dtsi | 15 +++++
2 files changed, 73 insertions(+)
@@ -113,6 +113,16 @@ vcc5v0_baseboard: vcc5v0-baseboard-regulator {
vin-supply = <&dc_12v>;
};
+ vcc5v0_otg: vcc5v0-otg-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ };
+
vcc5v0_usb: vcc5v0-usb-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_usb";
@@ -137,6 +147,10 @@ &combphy2_psu {
status = "okay";
};
+&extcon_usb3 {
+ status = "okay";
+};
+
&gmac0 {
status = "okay";
};
@@ -199,6 +213,13 @@ haikou_keys_pin: haikou-keys-pin {
<3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
+
+ usb2 {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins =
+ <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
&sdmmc {
@@ -214,6 +235,23 @@ &sdmmc {
status = "okay";
};
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ status = "okay";
+};
+
&u2phy2 {
status = "okay";
};
@@ -237,6 +275,13 @@ &uart2 {
&uart5 {
rts-gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
+};
+
+&usbdp_phy0 {
+ status = "okay";
+};
+
+&usbdp_phy1 {
status = "okay";
};
@@ -250,6 +295,19 @@ &usb_host0_ohci {
status = "okay";
};
+/* host0_xhci on Q7_USB_P1, usb3-otg port */
+&usb_host0_xhci {
+ dr_mode = "otg";
+ extcon = <&extcon_usb3>;
+ status = "okay";
+};
+
+/* host1_xhci on Q7_USB_P0, lower usb3 port */
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
/* host1 on Q7_USB_P3, usb2 port */
&usb_host1_ehci {
status = "okay";
@@ -23,6 +23,14 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
};
+ extcon_usb3: extcon-usb3 {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb3_id>;
+ status = "disabled";
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -327,6 +335,13 @@ module_led_pin: module-led-pin {
rockchip,pins = <1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
+
+ usb3 {
+ usb3_id: usb3-id {
+ rockchip,pins =
+ <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
&saradc {