arm64: dts: rockchip: add QNAP TS233 devicetree
From: Heiko Stuebner <heiko@...> Date: Mon, 19 Aug 2024 10:50:17 +0200
Commit-Message
The TS233 is a 2 bay NAS similar to the TS433. Architecture-wise it really seems to be the same minus the additional PCIe connected components the TS433 has. So it just uses two of the SoCs SATA ports and the SoC's gigabit ethernet. Signed-off-by: Heiko Stuebner <heiko@...>
Patch-Comment
arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3568-qnap-ts233.dts | 133 ++++++++++++++++++ 2 files changed, 134 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts
Statistics
- 134 lines added
- 0 lines removed
Changes
-------------------- arch/arm64/boot/dts/rockchip/Makefile ---------------------
index 099520962ffb..f1b7917ae22b 100644
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts233.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
-------------- arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts --------------
new file mode 100644
index 000000000000..29181de1bd26
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2024 Heiko Stuebner <heiko@sntech.de>
+ */
+
+/dts-v1/;
+
+#include "rk3568-qnap-tsx33.dtsi"
+
+/ {
+ model = "Qnap TS-233-2G NAS System 2-Bay";
+ compatible = "qnap,ts233", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac0;
+ };
+};
+
+/* connected to sata2 */
+&combphy2 {
+ status = "okay";
+};
+
+&gmac0 {
+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus>;
+ rx_delay = <0x15>;
+ tx_delay = <0x21>;
+ status = "okay";
+};
+
+&i2c1 {
+ /* eeprom for vital-product-data on the backplane */
+ eeprom@56 {
+ compatible = "giantec,gt24c04a", "atmel,24c04";
+ reg = <0x56>;
+ label = "VPD_BP";
+ num-addresses = <2>;
+ pagesize = <16>;
+ read-only;
+ };
+};
+
+&leds {
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+ label = "hdd2:green:disk";
+ linux,default-trigger = "disk-activity";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdd2_led_pin>;
+ };
+};
+
+&mcu {
+ compatible = "qnap,ts233-mcu";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@3 {
+ /* Motorcomm YT8521 phy */
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x3>;
+ pinctrl-0 = <ð_phy0_reset_pin>;
+ pinctrl-names = "default";
+ reset-assert-us = <10000>;
+ reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ gmac0 {
+ eth_phy0_reset_pin: eth-phy0-reset-pin {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ hdd2_led_pin: hdd2-led-pin {
+ rockchip,pins = <1 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&sata2 {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+/* connected to usb_host1_ehci/ohci */
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+/* connected to usb_host0_ehci/ohci */
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+/* right port backside */
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+/* left port backside */
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};