From: Heiko Stuebner <heiko.stuebner@...>
Date: Tue, 24 Mar 2020 00:06:28 +0100
The RE signal is used to control the duplex mode of transmissions,
aka receiving data while sending in full duplex mode, while stopping
receiving data in half-duplex mode.
On a number of boards the !RE signal is tied to ground so reception
is always enabled except if the UART allows disabling the receiver.
This can be taken advantage of to implement half-duplex mode - like
done on 8250_bcm2835aux.
Another solution is to tie !RE to RTS always forcing half-duplex mode.
And finally there is the option to control the RE signal separately,
like done here by introducing a new rs485-specifc gpio that can be
set depending on the RX_DURING_TX setting in the common em485 callbacks.
Signed-off-by: Heiko Stuebner <heiko.stuebner@...>
drivers/tty/serial/8250/8250_port.c | 11 ++++++++++-
drivers/tty/serial/serial_core.c | 12 ++++++++++++
include/linux/serial_core.h | 1 +
3 files changed, 23 insertions(+), 1 deletion(-)
@@ -1445,6 +1445,7 @@ static void serial8250_stop_rx(struct uart_port *port)
void serial8250_em485_stop_tx(struct uart_8250_port *p)
{
unsigned char mcr = serial8250_in_MCR(p);
+ struct uart_port *port = &p->port;
if (p->port.rs485.flags & SER_RS485_RTS_AFTER_SEND)
mcr |= UART_MCR_RTS;
@@ -1458,6 +1459,9 @@ void serial8250_em485_stop_tx(struct uart_8250_port *p)
* Enable previously disabled RX interrupts.
*/
if (!(p->port.rs485.flags & SER_RS485_RX_DURING_TX)) {
+ if (port->rs485_re_gpio)
+ gpiod_set_value(port->rs485_re_gpio, 1);
+
serial8250_clear_and_reinit_fifos(p);
p->ier |= UART_IER_RLSI | UART_IER_RDI;
@@ -1614,9 +1618,14 @@ static inline void __start_tx(struct uart_port *port)
void serial8250_em485_start_tx(struct uart_8250_port *up)
{
unsigned char mcr = serial8250_in_MCR(up);
+ struct uart_port *port = &up->port;
+
+ if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) {
+ if (port->rs485_re_gpio)
+ gpiod_set_value(port->rs485_re_gpio, 0);
- if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX))
serial8250_stop_rx(&up->port);
+ }
if (up->port.rs485.flags & SER_RS485_RTS_ON_SEND)
mcr |= UART_MCR_RTS;
@@ -3356,6 +3356,18 @@ int uart_get_rs485_mode(struct uart_port *port)
rs485conf->flags |= SER_RS485_TERMINATE_BUS;
}
+ port->rs485_re_gpio = devm_gpiod_get(dev, "rs485-rx-enable",
+ GPIOD_FLAGS_BIT_DIR_OUT);
+ if (IS_ERR(port->rs485_re_gpio)) {
+ ret = PTR_ERR(port->rs485_re_gpio);
+ port->rs485_re_gpio = NULL;
+ if (ret != -ENOENT) {
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Cannot get rs485-rx-enable-gpios\n");
+ return ret;
+ }
+ }
+
return 0;
}
EXPORT_SYMBOL_GPL(uart_get_rs485_mode);
@@ -252,6 +252,7 @@ struct uart_port {
const struct attribute_group **tty_groups; /* all attributes (serial core use only) */
struct serial_rs485 rs485;
struct gpio_desc *rs485_term_gpio; /* enable RS485 bus termination */
+ struct gpio_desc *rs485_re_gpio; /* gpio RS485 receive enable */
struct serial_iso7816 iso7816;
void *private_data; /* generic platform data pointer */
};