arm64: dts: rockchip: add usb typec host support to
From: Heiko Stuebner <heiko.stuebner@...> Date: Thu, 2 Nov 2023 13:33:15 +0100
Commit-Message
Jaguar has two type-c ports connected to fusb302 controllers that can work both in host and device mode and can also run in display-port altmode. While these ports can work in dual-role data mode, they do not support powering the device itself as power-sink. This causes issues because the current infrastructure does not cope well with dual-role data without dual-role power. So add the necessary nodes for the type-c controllers as well as enable the relevant core usb nodes, but limit the mode to host-mode for now until we figure out device mode. Signed-off-by: Heiko Stuebner <heiko.stuebner@...>
Patch-Comment
.../arm64/boot/dts/rockchip/rk3588-jaguar.dts | 178 ++++++++++++++++++ 1 file changed, 178 insertions(+)
Statistics
- 178 lines added
- 0 lines removed
Changes
---------------- arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts ----------------
index 90f823b2c219..329d98011c60 100644
@@ -333,6 +333,52 @@ rtc_twi: rtc@6f {
};
};
+ usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vcc_5v0_usb_c1>;
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ label = "USBC-1 P11";
+ power-role = "source";
+ source-pdos =
+ <PDO_FIXED(5000, 1500, PDO_FIXED_DATA_SWAP | PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc0_hs: endpoint {
+ remote-endpoint = <&usb_host0_xhci_drd_sw>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usbc0_ss: endpoint {
+ remote-endpoint = <&usbdp_phy0_typec_ss>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ usbc0_sbu: endpoint {
+ remote-endpoint = <&usbdp_phy0_typec_sbu>;
+ };
+ };
+ };
+ };
+ };
+
vdd_npu_s0: regulator@42 {
compatible = "rockchip,rk8602";
reg = <0x42>;
@@ -394,6 +440,52 @@ &i2c8 {
pinctrl-0 = <&i2c8m2_xfer>;
status = "okay";
+ usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vcc_5v0_usb_c2>;
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ label = "USBC-2 P12";
+ power-role = "source";
+ source-pdos =
+ <PDO_FIXED(5000, 1500, PDO_FIXED_DATA_SWAP | PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc1_hs: endpoint {
+ remote-endpoint = <&usb_host1_xhci_drd_sw>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usbc1_ss: endpoint {
+ remote-endpoint = <&usbdp_phy1_typec_ss>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ usbc1_sbu: endpoint {
+ remote-endpoint = <&usbdp_phy1_typec_sbu>;
+ };
+ };
+ };
+ };
+ };
+
vdd_cpu_big0_s0: regulator@42 {
compatible = "rockchip,rk8602";
reg = <0x42>;
@@ -851,6 +943,24 @@ &tsadc {
status = "okay";
};
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vcc_5v0_usb_c1>;
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ phy-supply = <&vcc_5v0_usb_c2>;
+ status = "okay";
+};
+
&u2phy2 {
status = "okay";
};
@@ -893,6 +1003,46 @@ &uart7 {
status = "okay";
};
+&usbdp_phy0 {
+ orientation-switch;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_typec_ss: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_ss>;
+ };
+
+ usbdp_phy0_typec_sbu: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usbc0_sbu>;
+ };
+ };
+};
+
+&usbdp_phy1 {
+ orientation-switch;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy1_typec_ss: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc1_ss>;
+ };
+
+ usbdp_phy1_typec_sbu: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usbc1_sbu>;
+ };
+ };
+};
+
/* host0 on P10 USB-A */
&usb_host0_ehci {
status = "okay";
@@ -903,6 +1053,34 @@ &usb_host0_ohci {
status = "okay";
};
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_host0_xhci_drd_sw: endpoint {
+ remote-endpoint = <&usbc0_hs>;
+ };
+ };
+};
+
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_host1_xhci_drd_sw: endpoint {
+ remote-endpoint = <&usbc1_hs>;
+ };
+ };
+};
+
/* host1 on M.2 E-key */
&usb_host1_ehci {
status = "okay";